联系我们

联系人: 刘经理 手机: 15953131568        18888346536 QQ: 408031499 网址: http://www.cishanfst.com 地址: 济南市天桥区金牛建材市场

新闻中心当前位置:秒速牛牛—新闻中心

安装电动卷帘门需要保证哪些问题?
来源:http://www.cishanfst.com  2019-12-26 15:44:55
电机更换后,检查线路,机械组织是否有疑问,卷帘门下有无障碍物,门下有无通道,调试后开始测试极限。电动卷帘门的极限机构设置在电动机壳体上,称为极限螺杆套筒滑块式。试运转前应先松开限位机构上的锁紧螺钉,然后拉动环链使门帘离地1米。
After the replacement of the motor, check whether there is any doubt about the circuit and mechanical organization, whether there is any obstacle under the roller shutter door, and whether there is any channel under the door, and start to test the limit after the commissioning. The limit mechanism of the electric rolling shutter door is arranged on the motor shell, which is called limit screw sleeve slide type. Before the test run, loosen the locking screw on the limit mechanism first, and then pull the chain to make the curtain 1 m above the ground.
第一次尝试“向上”、“停止”“下降”按钮,调查卷门上升,停止,每个函数下降不是宽松的和可靠的,如果正常的上升或者下降的门帘可以确定方位,然后旋转螺旋套管的极限,适应触动微动开关辊,听到“滴答”的声音,收紧锁螺丝。反复调试使限位达到最佳位置,然后拧紧锁紧螺丝。安装电动卷帘门主扇。一定要保证电动卷帘门和墙面形成一个整体,关好后,再把洞口和墙面油漆好。粉刷完毕后,门缝应均匀平整,打开电动卷帘门应轻便自由,不得有过紧、过松和回弹现象。西安电动卷帘门安装流程:

For the first time, try the "up", "stop" and "down" buttons to investigate the rise and stop of the rolling door. Each function decline is not loose and reliable. If the normal rise or fall curtain can determine the direction, then rotate the limit of the spiral casing, adapt to touch the micro switch roller, hear the "tick" sound, and tighten the locking screw. Repeatedly adjust the limit to the best position, and then tighten the locking screw. Install the main fan of the electric rolling shutter door. Make sure that the electric rolling shutter door and the wall form a whole, and paint the hole and the wall after closing. After painting, the door joint shall be even and flat, and the opening of the electric roller shutter door shall be light and free without over tightening, over loosening and rebound. Xi'an electric roller shutter installation process:

1,首先需求的设备门框口方位画一条线,表明规模的大小,然后找到合适的设计人员电动百叶窗滚(这里值得注意的是,框架的高度略高于门的高度)。
1. Draw a line at the door opening of the required equipment to indicate the size of the scale, and then find a suitable designer for the electric shutter roll (it is worth noting that the height of the frame is slightly higher than the height of the door).
2、门框的电动卷帘门固定好了,这里要拆下门框下方的固定板(注:孔两侧要预留凹槽,经校对合格后,固定木楔,门框铁脚与预埋铁板焊接。
2. The electric rolling shutter door of the door frame is fixed. Here, the fixed plate under the door frame shall be removed (Note: grooves shall be reserved on both sides of the hole. After being checked to be qualified, the wooden wedge shall be fixed, and the iron foot of the door frame shall be welded with the embedded iron plate.
3、本装置电动卷帘门主扇。一定要保证电动卷帘门与墙面形成一个整体,合拢要做好,然后把洞口和墙面油漆好。上漆后,门缝应平整平整,开电动卷帘门应自由简单,不能有过紧、过松和反弹的景象。
3. The main fan of the electric rolling shutter door of the device. Make sure that the electric rolling shutter door and the wall form a whole, close well, and then paint the hole and the wall. After painting, the door seam shall be flat and flat, and the opening of the electric rolling shutter door shall be free and simple, and shall not be too tight, too loose or rebound.
以上内容由http://www.cishanfst.com发布
The above content is published by http://www.cishanfst.com
荣鼎彩开奖 ag真人 贵州快3走势 湖南快乐十分走势 吉林快三机器人 秒速牛牛计划 任我赢机器人 上海11选5走势图 领航机器人 河北快3开奖