欢迎光临济南宏顺卷帘门厂官网!

联系我们 收藏本站 在线留言

新闻资讯

秒速牛牛>>新闻资讯>>济南卷帘门电机安装及限位调试
新闻资讯
联系我们
济南宏顺卷帘门厂

联系人:刘经理

电话:15953131568

网址:http://www.cishanfst.com

地址:济南市天桥区金牛建材市场

济南卷帘门电机安装及限位调试

来源:http://www.cishanfst.com 日期:2020-06-13 发布人:hongshun
1、电机更换安装
1. Motor replacement and installation
济南卷帘门的电机与卷筒芯轴之间是由传动链条来连接,电机地脚用螺钉固定在链轮支架板上。更换电机前,必须将卷帘门降至端或用支架将卷帘门撑住。这是因为一是卷帘门的制动是靠电机本体上的制动器来起作用,电机拆除后,卷帘门则没有制动而自动下滑;二是可以使传动链条放松,方便将链条取下。
The motor of the electric rolling shutter door is connected with the mandrel of the drum by the transmission chain, and the motor foundation is fixed on the sprocket support plate with screws. Before replacing the motor, the roller shutter must be lowered to the lowest end or supported by a bracket. This is because the first is that the brake of the rolling shutter door depends on the brake on the motor body. After the motor is removed, the rolling shutter door will slide down automatically without brake; the second is that the transmission chain can be relaxed to facilitate the removal of the chain.
更换电机的步骤:将电机接线做好标记然后拆除,将电机地脚螺丝拧松将传动链条摘下,将电机地脚螺丝拆除将电机取出;新电机安装顺序相反,但要注意,电机安装好后,其本体上的环形手拉链条应自然垂直向下,不得有卡阻现象。
Steps to replace the motor: mark the motor wiring, remove it, loosen the motor anchor screw, remove the drive chain, and finally remove the motor anchor screw to take out the motor; the installation sequence of the new motor is reverse, but it should be noted that after the motor is installed, the ring-shaped hand zipper bar on the body should be naturally vertical downward, without jamming.
2、限位调试
2. Limit debugging
电机更换完毕后,检查线路、机械机构均无问题,卷帘门下方无障碍物,门下禁止通行,确认后开始试车调试限位。卷帘门的限位机构是安装在电机外壳上,称为限位螺套滑块式。试机前应先松开限位机构上的锁紧螺钉,然后用手拉动环形链条使门帘离地面1米左右,先试“上”、“停”、“下”按键,观察卷门升、停、降各功能是否灵敏可靠,若正常即可将门帘上升或下降到确定的位置,然后旋转限位螺套,调整碰至微动开关滚轮,听到“滴答”声后,拧紧锁紧螺钉。反复调试,使限位达到位置时,再将锁紧螺钉用力旋紧即可。
After the replacement of the motor, check whether there is any problem in the circuit and mechanical mechanism, no obstacle under the roller shutter door, and no access under the door. After confirmation, start the commissioning and limit. The limit mechanism of the rolling shutter door is installed on the motor shell, which is called limit screw sleeve sliding block type. Before the test, loosen the locking screw on the limit mechanism, then pull the circular chain by hand to make the door curtain about 1 meter away from the ground, first test the "up", "stop" and "down" buttons, observe whether the functions of the rolling up, stop and down are sensitive and reliable, if it is normal, the door curtain can be raised or lowered to a certain position, then rotate the limit screw sleeve, adjust and touch the microswitch roller, hear“ After the "tick", tighten the locking screw. Repeat the debugging to make the limit reach the best position, and then tighten the locking screw.
以上新闻由济南宏顺卷帘门公司发布,公司网址: http://www.cishanfst.com  ,济南宏顺卷帘门
The above news is released by Jinan Hongshun rolling shutter door Co., Ltd. website: http://www.cishanfst.com   , Jinan Hongshun rolling shutter

推荐阅读/ Recommended reading

在居民入户里面我们要安装家庭门,同时为了商铺的安全我们也会选择安装卷帘门,卷帘门的安装重要吗,答案是肯定的。接下来我们对它有个具体

济南卷帘门三大故障的排除方法 2020-06-23
卷帘门电机的选择机及使用事项 2020-06-20
济南卷帘门常见的故障是什么? 2020-06-18
卷帘门两种故障的原因介绍 2020-06-16

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

  • 济南市天桥区昌达卷帘门加工部
北京快3 新疆喜乐彩 北京赛车Pk10全自动下注微信群机器人 河北快3 荣鼎彩投注 领航机器人 广西快3走势 福彩3D 福建11选5 山东11选5走势